Home >

Leaf Eater Advanced 3 inch or 4 inch from Rain Harvesting Pty by Blue Mountain Co.
leaf eater advanced PN RHAD99 and RHAD98 now replaced by RHAD100


 
Alternative Views:
List Price: $52.95
Our Price: $33.95
Updated Price: $33.95
You save $19.00!

Availability:: Pre-Order
Product Code: FILTLEA

  
Description Technical Specs
 

Rain Harvesting Pty Leaf Eater Advanced - now available with an adaptable 3 in. or 4 in. adapters for downspouts in one product.

Keeps your Rain Harvesting system free of mosquitoes, vermin, and debris
  • Compact, versatile rain head for quick and easy installation
  • New design now includes adapters for BOTH a 3" and a 4" outlet
  • Patented single screen technology for advanced debris shedding (Clean Shield™)
  • Minimal maintenance
  • Pivot the outlet to suit vertical or horizontal (rear outlet) downpipes – a variety of installation options in one product (VH Pivot™ patent pending)
  • High flow rate performance
  • Superior catchment efficiency at low and high flow rates
  • Single screen with 0.955mm aperture mosquito proof stainless steel mesh

The Leaf Eater AdvancedTM can also be used as a debris removing device even when rainwater is not being collected.



Installation Instructions

Gutter & Mid-Mount Installation

1. Gutter: Measure 208mm from the bottom of the existing gutter pop and remove this section of the downpipe. Ensure the cut edge is clean and smooth. Mid-Mount: Remove 208mm of downpipe where the Leaf Eater Advanced™ is to be situated. Ensure all cut edges are clean and smooth.
2. Using the quick-release tabs remove the Cleanshield™ screen by lifting it up and then out.
3. Insert the Leaf Eater Advanced™ by sliding it up over the cut section and then down into position. The Leaf Eater Advanced™ outlet should be slid firmly onto the bottom downpipe until it can be pushed no further.
4. Screw the Leaf Eater Advanced™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used.
5. Insert the Cleanshield™ screen into the Leaf Eater Advanced™. Ensure the Cleanshield™ screen is sitting firmly in place and check installation is secure.



Horizontal (Rear Outlet) Installation

1. Using the quick-release tabs remove the Cleanshield™ screen by lifting it up and then out.
2. Swivel the outlet to the horizontal position – some force may be required.
3. Position the Leaf Eater Advanced™ next to existing pipework, mark and cut top and bottom cut lines... Ensure that the cut edge is clean and smooth.
4. Insert the Leaf Eater Advanced™ by sliding the rear outlet into the horizontal pipe. The back fixing plate must sit behind the top section of the downpipe.
5. Screw the Leaf Eater Advanced™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used.
6. Insert the Cleanshield™ screen into the Leaf Eater Advanced™. Ensure the Cleanshield™ screen is sitting firmly in place and check the installation is secure.
Features
  • Compact, versatile rain head for quick and easy installation
  • Patented single screen technology for advanced debris shedding (Clean Shield™)
  • Minimal maintenance
  • Pivot the outlet to suit vertical or horizontal (rear outlet) downpipes – variety of installation options in one product (VH Pivot™ patent pending)
  • High flow rate performance
  • Superior catchment efficiency at low and high flow rates
  • Single screen with 0.955mm aperture mosquito proof stainless steel mesh
  • Available in 90mm or 100mm outlet

Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 1 Write a review.

  0 of 0 people found the following review helpful:
 
5 of 5 Works Great! September 5, 2020
Reviewer: Randall H from Boone , NC United States  
I recently installed one of the Leaf Eaters during a French drain project. It worked great. I recommend installing it close to ground level as I find myself cleaning it after every downpour.
Well worth the money.

Was this review helpful to you?